Feline guitars repairs london surrey
 
 
 

Fretwork - our speciality

The frets on your guitar are just about the most important thing affecting the playability of the instrument, and as such deserve special attention.

Whilst most guitars will benefit from a set-up, often you won’t get the full benefit from that process because of issues with the frets:
It may be that there is wear in certain areas of the frets, or that through shrinkage in the fingerboard (or other reasons), some frets are slightly higher than others resulting in rattle, buzz or choking when bending strings.
This is something that would usually be diagnosed in our free health check process.

Other times players just want to get the most out of their guitars and careful fretwork is the key to achieving this.
By getting the frets all perfectly level with each other, and then doing a careful set-up a much better end result is achieved.

 

 

Fret Dressing - the great leveller

This is the process that starts to give us the control we need to make your guitar play to it’s fullest capacity.
All guitars in their lifetime will benefit from a fret dress at some point or other.
The Erlewine / Stewmac neck jig (see pic on right)
We were early adopters of the neck jig in 1999 and have used it ever since for EVERY full fret dress we do.
We wouldn’t want to be without it, especially as we know how to get the best out of it.

What does the neck jig do?

It allows us to recreate the same tensions on a neck as created by the pull of the strings, but without the strings on, thus allowing you to work on the frets, with the neck in it’s optimum state to be levelled.

What some others might call a fret dress :– running a worn out oilstone up and down the frets, often simply following the humps and bumps already in the neck, thus failing to eliminate the problems isn't the way to do it.

We prefer to skim ALL the frets at once with a precision ground leveller to ensure that we are working on a completely level surface and that all the frets are taken into account when we level.
This removes any high spots from end to end.
We level in the “lie of the strings” even if the fingerboard’s radius is based on a true cylinder .
This will create a slight compound radius which again is essential for low action with choke free string bends.
We also introduce a small amount of “fall-away” into the last few frets.
This allows for the elliptical movement of the strings not to end up hitting the last frets as you play higher up the fingerboard.
We also introduce an exaggerated compound radius at the top end of the board on the treble side to try to help with big bends on the high E (and B) strings.
The frets are neatly re-profiled to a proper clean domed shape using a diamond coated tool followed by higher grades of abrasive paper, and finally polished to a high gloss finish.
NOW we can do a good set-up on the guitar.

Re-fretting

This process allows us the most control over the whole set-up process as we can correct any imperfections in the fingerboard, as well as controlling the frets.

There are a number of reasons for a re-fret to be required:

Maybe the frets are worn out or badly pitted, and simply dressing the frets to remove the wear would leave a fret that is too low for the players comfort or to let the guitar play at it’s best.

Sometimes the height or profile of the existing frets are not ideal for the player and they would like to change gauge.
We keep a wide selection of wires in stock from vintage to super-jumbo.

Whichever is the case we can help.
The time consuming processes involved in doing a re-fret are very important to the end result.
The better your preparation, then the better the end result will be.

We take a lot of care in the treatment of the fingerboard itself to give the best possible surface to install the new frets.
Our installation process is equally detailed, with utmost care being taken to ensure a firm and tidy seating of each fret - to maximise tone & neck stiffness, also ensuring consistent feel and reliability for years to come.

The way we finish the ends of our frets flush to the edge of the board in a way that you hardly feel them and never snag yourself on the ends is almost our trademark.
Subsequent to this we then fret dress and set-up the guitar as per above.

Tel: +44 (0)20 8680 9131 | www.felineguitars.com | design by concrete
All registered trademarks are used for retail & descriptive purposes. Feline Guitars is not affiliated with either Floyd Rose or Earvana.